CADDX NX-6 Installationshandbuch Seite 39
- Seite / 104
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
GE Security
g
Segment 2
1 = Zone and box tamper
2 = Auxiliary power overcurrent, and restore
3 = Wireless sensor missing and restore
4 = Wireless sensor low battery and restore
5 =
Expander trouble and restore (keypads are considered as
expanders)
6 = Fail to communicate
7 = Alarm restore
8 = Tamper restore
LOCATION 11 - PARTITIONS REPORTED TO PHONE N° 2 (1 segment, feature selection data)
Location 11 is used when events to be reported to a phone number are based on the
partition, regardless of the event. If this location is used, location 10 should be “0”.
Segment 1
1 = Partition 1
2 = Partition 2
3-8 Reserved
Telephone number 3
LOCATION 12 - PROGRAMMING PHONE N° 3 (20 segments, numerical data)
Phone N°3 is programmed in location 12. A “14” indicates the end of the phone number.
Delays of four seconds can be programmed at any point in the phone number by
programming a “13” in the appropriate segment. The system will always wait for a dial
tone unless the first digit of the phone number is a “13”; in this case, it will only delay.
Tone (DTMF) dialling is default. If you want pulse tone dialling, program a “15” in the
segment where pulse dialling should begin. If the entire number should be pulse dialling,
program a “15” in the first segment. Program an “11” for a “*”, and a “12” for a “#”.
Note: a zero is programmed as a “0”.
LOCATION 13 - ACCOUNT CODE FOR PHONE N° 3 (6 segments, numerical data)
Use location 13 to program the account code that is sent when phone N°3 is dialled. A
zero in the account code is programmed as a “0”. A “10” indicates the end of the account
code, so program a “10” in the segment immediately after the last digit of the account
code. If the account code is 6 digits long, program all 6 segments. If location 6 is left un-
programmed, account code 1 will be used when phone N°3 is dialled.
LOCATION 14 - COMMUNICATOR FORMAT FOR PHONE N° 3 (1 segment, numerical data)
Location 14 contains the communicator format used to transmit to the receiver that is
connected to phone N°3. Consult the instruction manual for your central station receiver
in order to determine which format is compatible, and select from the 15 formats listed on
page 33. If you require a format other than those listed, review the override options
described in location 18 to create the appropriate format. In order to create a special
format, a “15” must be programmed in location 14, in addition to the entries in location 18.
If this location contains a “0”, format 1 will be used when phone N°3 is dialled.
NX-6-EUR Installation manual Page 39 23/12/04
- Series 1
- NX-6-EUR Control Panel 1
- Installation manual 1
- CONTENTS 3
- GENERAL INFORMATION 5
- ORDERING INFORMATION 5
- FEATURE DEFINITIONS 6
- GE Security 10
- PROGRAMMING THE NX-6 KEYPADS 14
- IMPORTANT REMARKS 33
- Telephone number 1 34
- Format selections 35
- Telephone number 2 37
- Telephone number 3 39
- Special formats 42
- Download parameters 43
- Entry/Exit timers 45
- General options 50
- Programming the outputs 54
- NX-6 PROGRAMMING WORKSHEETS 79
- BOARD INSTALLATION 90
- NX-6 WIRING DIAGRAM 91
- TERMINAL DESCRIPTION 92
- TECHNICAL SPECIFICATIONS 93
- CONTACT-ID AND SIA 95
- CONTACT ID 97
- EXPANDER TROUBLE 99
- CE DECLARATION 100
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme CADDX NX-6
(18 Seiten)ParkZone PKZ1400 manuels
Manuels d'utilisation et guides de l'utilisateur pour Jouets ParkZone PKZ1400.
Nous fournissons des manuels en pdf 2 ParkZone PKZ1400 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Kommentare zu diesen Handbüchern