CADDX NX-408E-I Installationshandbuch Seite 40
- Seite / 99
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 2: Reporting codes
36 NX-8V2 Control Panel Installation Manual
Segment 2 - AC fail report delay in minutes, 0 to 255 (0 = no delay). Default is 5.
Segment 3 - Power up delay in seconds, 0 to 60 (0 = no power up delay). Default is 60.
Segment 4 - Siren time in minutes, 1 to 254. Default is 8.
Segment 5 - Telephone line cut delay in seconds, 0 to 255 (0 = no monitoring). Default is 0.
Segment 6 - Cross zone time in minutes, 0 to 255 (0 = no cross zoning). Default is 5.
Segment 7 - Chime time in 50 mS increments from 0 to 12 seconds. Default is 3.
Segment 8 - Dial delay in seconds, 15 to 255 (0 = no abort delay). Default is 30.
Segment 9 - Fire alarm verification time in seconds, 120 to 255 (0 = no fire alarm verification).
Default is 0. This feature is not approved for residential use in California.
Segment 10 - Listen-in time in seconds, 0 to 255 (0 = no listen in time). Default is 0.
Segment 11 - Zone activity monitor feature timed in days, 0 to 255 (0 = disabled). Default is 0.
Segment 12 to 14 - Reserved
Location 41 - Special features
Location 41 has one segment of feature selection data.
Segment 1
1. On enables the six-digit code option. If enabled, all arm/disarm codes and the go to program
code are six digits. The default user 1 code is 123456.
Caution: If you enable this option verify that the go to program code is a six-digit code before
exiting programming.
2. On requires code entry for *, 9, 8 (dial call back phone number) and *, 9, 9 (answer incoming
call for download) functions.
3. On enables auto cancel/abort.
4. On enables walk test mode.
5. On enables auto force arming with keyfob or keyswitch.
6 to 8 Reserved.
Locations 42 and 43 - Go to program code and
authorization
Location 42 - Go to program code
Location 42 has six segments of numerical data. Use this location to program the
go to program code. This location contains either a four or six-digit code. If the
six-digit code option is enabled in Location 41, this code must contain six digits. If
not enabled in Location 41, the last two segments (digits) are ignored. With the
NX-8V2 disarmed, use the go to program code to enter program mode. Defaults
for segments 1 to 6 are 9. 7, 1, 3, 0, 0.
- NX-8V2 Control Panel 1
- Installation Manual 1
- Content 3
- Important information 4
- Chapter 1 5
- Introduction 5
- Product overview 6
- Board installation 7
- Chapter 1: Reporting codes 8
- Terminal descriptions 9
- Module list 10
- Chapter 1: Reporting codes 11
- Chapter 2 13
- Programming 13
- Chapter 2: Reporting codes 14
- LED keypad programming 15
- Elapsed increments 16
- System date 16
- Keypad number and partition 16
- System clock 17
- User codes 17
- User authority level 17
- Control panel programming 18
- Chapter 2: Reporting codes 19
- Programming data types 20
- Loading factory defaults 21
- Programming locations 23
- Location 40 - System timers 39
- Location 44 - Duress code 41
- Chapter 3 57
- Troubleshooting 57
- General diagnosis 58
- Trouble conditions 58
- Chapter 3: Reporting codes 59
- Voltage tables 60
- Specification 61
- Chapter 3: Reporting codes 62
- Appendix A 63
- Reporting codes 63
- Appendix A: Reporting codes 64
- (Locations 110 to 169) 66
- Appendix B 71
- Programming worksheet 71
- Glossary 91
- Glossary 93
Verwandte Produkte und Handbücher für Empfänger CADDX NX-408E-I
Empfänger CADDX NX-408E-I Spezifikationen
(16 Seiten)
(16 Seiten)
Empfänger CADDX NX-408E Spezifikationen
(16 Seiten)
(16 Seiten)
Empfänger CADDX NX-448E-I Spezifikationen
(30 Seiten)
(30 Seiten)
Empfänger CADDX NX-448E-I Installationshandbuch
(61 Seiten)
(61 Seiten)
ParkZone PKZ3400 manuels
Manuels d'utilisation et guides de l'utilisateur pour Jouets ParkZone PKZ3400.
Nous fournissons des manuels en pdf 1 ParkZone PKZ3400 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Kommentare zu diesen Handbüchern