CADDX NX-448E-I Spezifikationen

Caddx® Installation Instructions PackageThis package includes instructions for the following Caddx products: NetworX NX Series Receiver Modules—NX-40

Page 8NetworX NX Series Receiver Modules40 (Zone 40)Assigned to module #_____.1 - Enable sensor ❏2 - Supervised ❏3 - Input option 1 ❏4 - Input option

NetworX NX Series Receiver ModulesPage 9Enroll the ModuleThe following steps describe how to enroll and program the module to be supervised by the NX-

Page 10NetworX NX Series Receiver Modules5) Enter [4] [9] [#] to enter the sensor learning location. The Ready LED should turn on and the Armed LED sh

NetworX NX Series Receiver ModulesPage 118) Press [✻] to save any changes. The panel is now wait-ing for the next location entry.Note: Pressing [#] do

Page 12NetworX NX Series Receiver Modules5) Enter the tripped transmitters’ location.6) Observe keypad light 7 which should be on, indicating the tran

NX-450, NX-451 Door/Window SensorsPage 1NX-450, NX-451 Door/Window SensorsDocument Number: 466-1303-CDX Rev. BSeptember 1997InstallationInstructionsPr

Page 2NX-450, NX-451 Door/Window SensorsFigure 3. Mounting Hole Locations (Bottom View)4. Remove the magnet from its base. Line up the arrow on the ma

NX-450, NX-451 Door/Window SensorsPage 3To replace a sensor:1. Test a known good sensor at the same location.2. If the system does not respond, avoid

Page 4NX-450, NX-451 Door/Window SensorsCaddx Controls, Inc. 1420 North Main Street Gladewater, Texas 75647Toll Free: 1-800-727-2339 FAX: (903) 84

Page 1Door/Window SensorDoor/Window SensorDocument Number: 466-1578 Rev. BMay 1998INSTALLATIONINSTRUCTIONSProduct SummaryThe Door/Window Sensor can be

Page 2Door/Window SensorFigure 1. Alignment marks2) Remove the sensor cover by squeezing the cover ends firmly to release the tab on the cover from th

Door/Window SensorPage 3Installation Guidelines Do not use solid core wire. Do not use mechanical switches. If you are connecting an external devic

Page 4Door/Window SensorSpecificationsFrequency: 433 MHz.OperatingTemperature Range: 10° to 120° F.Compatibility: NX-408-I, NX-416-I, and NX-448-IPowe

NX-470 Keychain TouchpadPage 1NX-470 KeyChain TouchpadDocument Number: 466-1478 Rev. EMay 1998InstallationInstructionsProduct SummaryKeychain Touchpad

Page 2NX-470 KeychainCaddx Controls, Inc. 1420 North Main Street Gladewater, Texas 75647Toll Free: 1-800-727-2339 FAX: (903) 845-6811Caddx is a reg

NX-480 Wireless Motion SensorPage 1NX-480 WirelessMotion SensorDocument Number: 466-1479 Rev. DMay 1998InstallationInstructionsProduct SummaryA motion

Page 2NX-480 Wireless Motion SensorFigure 1. Overhead (Bird’s Eye View) Detection Path For best coverage, mount the sensor from 5 to 8 feet high in t

NX-480 Wireless Motion SensorPage 3Mounting the SensorThe sensor can be flush-mounted, incline-mounted, or corner-mounted depending on the application

Page 4NX-480 Wireless Motion Sensor1. Locate the sensitivity pins by first removing the mounting plate and the sensor cover as described in steps 1 an

NX-480 Wireless Motion SensorPage 5Figure 7. PIR Components, Battery Locations, & Tamper SwitchFinal TestingFinal testing should be done to verify

NetworX NX Series Receiver ModulesPage 1NetworX NX Series Receiver ModulesDocument Number: 466-1427 Rev. EAugust 1998InstallationInstructionsProduct S

Page 6NX-480 Wireless Motion SensorCaddx Controls, Inc. 1420 North Main Street Gladewater, Texas 75647Toll Free: 1-800-727-2339 FAX: (903) 845-681

Page 2NetworX NX Series Receiver Modules3) Install the module into the cabinet by turning the stand-off sideways, then slide the module up onto the gr

NetworX NX Series Receiver ModulesPage 35) Apply power to the NX-8. The middle (red) LED on the module should start blinking. Table 2 describes the mo

Page 4NetworX NX Series Receiver ModulesTable 3. Module Programming Worksheet TableLocation Segment 1 Segment 20 (Supervi-sion)1 - Normal ______hrs.(0

NetworX NX Series Receiver ModulesPage 510 (Zone 10)Assigned to module #_____.1 - Enable sensor ❏2 - Supervised ❏3 - Input option 1 ❏4 - Input option

Page 6NetworX NX Series Receiver Modules20 (Zone 20)Assigned to module #_____.1 - Enable sensor ❏2 - Supervised ❏3 - Input option 1 ❏4 - Input option

NetworX NX Series Receiver ModulesPage 730 (Zone 30)Assigned to module #_____.1 - Enable sensor ❏2 - Supervised ❏3 - Input option 1 ❏4 - Input option