CADDX NX-448E-I Installationshandbuch Seite 42
- Seite / 113
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 2: Reporting codes
38 NX-8E Control Panel Installation Manual
Location 46 - Auxiliary outputs 1 to 4 special timing
Location 46 has four segments of feature selection data. Use this location to
program the special timing feature activation for the four auxiliary outputs.
Segment 1 corresponds to output 1, segment 2 to output 2, etc.
Segment 1 to 4 - Outputs 1 to 4
1. On if output is timed in minutes; off if timed in seconds.
2. On if output latches; off if output is timed.
3. On if output stops timing upon code entry; off if the output continues to time upon code entry.
4. On if output only activates between the closing and opening time (Locations 52 and 53).
5. On if output only activates between the opening and closing time (Locations 52 and 53).
6. On to invert the output. If the output is normally on when an event occurs, if you invert the
output it will be off when the event occurs.
7 and 8. Reserved.
Location 47 - Auxiliary output 1 event and times
Location 47 has two segments of numerical data.
Segment 1 - Use Table 8 on page 39 to select the event that activates auxiliary output 1. Default
is 0.
Segment 2 - Program the timing from 0 to 255 (minutes or seconds, depending on data
programmed in Location 46, segment 1). Programming a 0 makes the output follow the event.
Default is 10 (seconds)
Location 48 - Auxiliary output 2 event and times
Location 48 has two segments of numerical data.
Segment 1 - Use Table 8 on page 39 to select the event that activates auxiliary output 2. Default
is 1.
Segment 2 - Program the timing from 0 to 255 (minutes or seconds, depending on data
programmed in Location 46, segment 1). Programming a 0 makes the output follow the event.
Default is 10 (seconds).
Location 49 - Auxiliary output 3 event and times
Location 49 has two segments of numerical data.
Segment 1 - Use Table 8 on page 39 to select the event that activates auxiliary output 3. Default
is 21.
Segment 2 - Program the timing from 0 to 255 (minutes or seconds, depending on data
programmed in Location 46, segment 1). Programming a 0 makes the output follow the event.
Default is 10 (seconds).
- NX-8E Control Panel 1
- Installation Manual 1
- Content 3
- Important information 4
- Chapter 1 5
- Introduction 5
- Product overview 6
- Board installation 7
- Chapter 1: Reporting codes 8
- Terminal descriptions 9
- Module list 10
- Chapter 1: Reporting codes 11
- Chapter 2 13
- Programming 13
- Chapter 2: Reporting codes 14
- LED keypad programming 15
- Keypad number and partition 16
- Elapsed increments 16
- System date 16
- System clock 17
- User codes 17
- User authority level 17
- Control panel programming 18
- Chapter 2: Reporting codes 19
- Programming data types 20
- Loading factory defaults 21
- Programming locations 22
- Location 40 - System timers 39
- Location 44 - Duress code 41
- Chapter 3 63
- Troubleshooting 63
- General diagnosis 64
- Trouble conditions 64
- Chapter 3: Reporting codes 65
- Chapter 3: Reporting codes 66
- Voltage tables 67
- Specifications 68
- Appendix A 69
- Reporting codes 69
- Appendix A: Reporting codes 70
- (Locations 110 to 169) 72
- Appendix B 79
- Programming worksheet 79
- Zone worksheet 102
- Glossary 105
- Glossary 107
Verwandte Produkte und Handbücher für Empfänger CADDX NX-448E-I
Empfänger CADDX NX-448E-I Installationshandbuch
(94 Seiten)
(94 Seiten)
Empfänger CADDX NX-408E-I Installationshandbuch
(99 Seiten)
(99 Seiten)
Empfänger CADDX NX-408E-I Spezifikationen
(16 Seiten)
(16 Seiten)
Empfänger CADDX NX-408E Spezifikationen
(16 Seiten)
(16 Seiten)
Empfänger CADDX NX-448E-I Spezifikationen
(30 Seiten)
(30 Seiten)
Empfänger CADDX NX-448E-I Installationshandbuch
(61 Seiten)
(61 Seiten)
ParkZone PKZ4400 manuels
Manuels d'utilisation et guides de l'utilisateur pour Jouets ParkZone PKZ4400.
Nous fournissons des manuels en pdf 1 ParkZone PKZ4400 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Kommentare zu diesen Handbüchern