CADDX NX-448E-I Spezifikationen Seite 4
- Seite / 30
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Page 2
NetworX NX Series Receiver Modules
3) Install the module into the cabinet by turning the stand-
off sideways, then slide the module up onto the ground
plane screw posts (see Figure 3).
Figure 3. Installing the Module into the Cabinet
4) Turn the standoff so the slot is facing up, insert the
back corner of the module into the standoff slot, then
press up at the front of the standoff and tighten the
standoff screw.
5) Insert the antennas through the holes on top of the cab-
inet and into the module antenna sockets (see Figure
4).
Figure 4. Inserting the Antennas
Wiring, Module Number DIP Switch
Settings, and Power Up
The following steps describe wiring the module to the NX-
8, setting the module number DIP switches, and powering
up the NX-8.
1) Remove power (if applied) from the NX-8 control
panel.
CAUTION: To avoid possible equipment damage or per-
sonal injury, remove power from the NX-8
control panel before making any wiring con-
nections to the module.
2) Connect the module power and data terminals to the
NX-8 power and data terminals using 22-gauge or
larger, stranded wire (see Figure 5).
Figure 5. Wiring the Module Power and Data Terminals
to the NX-8 Power and Data Terminals
3) Set the module DIP switches to the desired module
number (see Table 1).
4) If using a NX-408 or NX-416, set DIP switch 3 to
enable zone blocks for transmitter learning as follows:
OFF = zones 9-16 or 9-24 enabled for learning
ON = zones 1-8 or 1-16 enabled for learning
9740G04A.DS4
9740G10A.DS4
Table 1. NX Module Number Settings
Module Number 32 Module Number 33
Module Number 34 Module Number 35
9740G14A.DS4
POWER + (TO NX-8 AUX PWR +)
GND (TO NX-8 COM)
DATA (TO NX-8 KP DATA)
ON
1 2
43
EDG
ON
1 2
43
EDG
ON
1 2
43
EDG
ON
1 2
43
EDG
- NetworX NX Series 3
- Receiver Modules 3
- Settings, and Power Up 4
- Location Segment 1 Segment 2 6
- (cont.) 6
- Enroll the Module 11
- Program the Module 11
- Programming Guidelines 11
- Settings 12
- Testing Wireless Transmitters 13
- Specifications 14
- U.L. Listings 14
- NX-450, NX-451 Door/ 15
- Window Sensors 15
- 8888G01A.DS4 16
- MOUNTING HOLES 16
- Door/Window 19
- Connecting External Switches 20
- Programming 21
- Testing Door/Window Sensors 21
- FCC Notice 22
- NX-470 KeyChain 23
- Touchpad 23
- NX-470 Keychain 24
- NX-480 Wireless 25
- Motion Sensor 25
- Animal Alley Lens Guidelines 26
- Mounting the Sensor 27
- Setting the Sensitivity 27
- Maintenance 28
- Final Testing 29
- NX-480 Wireless Motion Sensor 30
Verwandte Produkte und Handbücher für Empfänger CADDX NX-448E-I
Empfänger CADDX NX-448E-I Installationshandbuch
(61 Seiten)
(61 Seiten)
ParkZone PKZ3400 manuels
Manuels d'utilisation et guides de l'utilisateur pour Jouets ParkZone PKZ3400.
Nous fournissons des manuels en pdf 1 ParkZone PKZ3400 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Kommentare zu diesen Handbüchern