CADDX NX-6 Installationshandbuch Seite 18
- Seite / 104
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
GE Security
g
Programming the NX-148 LCD keypads
This section describes how to program the address and partition for each keypad, and it
also explains the options that are available. The address of the keypad is important
because the panel uses it to supervise the keypads.
The factory default for the Master code is [1]-[2]-[3]-[4] when using a 4-digit code, or [1]-
[2]-[3]-[4]-[5]-[6] for a 6-digit code. The factory default for the “Go To Program” code is
[9]-[7]-[1]-[3] when using a 4-digit code, or [9]-[7]-[1]-[3]-[0]-[0] for a 6-digit code.
[*]-[9]-[1] ADJUSTING THE VIEW / BRIGHTNESS OF THE LCD
1. Enter [*]-[9]-[1] The LCD screen will prompt for a “master” code.
2. Enter [master code]
The LCD will now prompt you to increase or reduce
the viewing angle. By using the scroll keys to the
right of the LCD, you can increase or reduce the
text-viewing angle.
3.
To advance to the brightness
option, press [*]
The LCD will prompt you to brighten or dim the
LCD lighting. Use the scroll keys again to set the
desired brightness. When completed, exit by
pressing [*].
[*]-[9]-[2] PROGRAMMING CUSTOM MESSAGES IN THE KEYPAD
1. Enter [*]-[9]-[2]
The LCD screen will prompt for the “Go To
Program” code.
2. Enter [program code]
The LCD will now prompt you to enter the message
number followed by [#]. Zones 1 through 16 custom
messages are message numbers 1-16
respectively.
Message 193 - Custom message top line.
Message 194 - Custom message bottom line.
Message 195 – Shutdown message top line.
Message 196 – Shutdown message bottom line.
3.
Enter message number to
edit, followed by [#]
The LCD will display the zone number on the top
line. The zone description will be displayed on the
bottom line. Use the instructions on page 29-30 to
edit character data.
4.
When finished, exit by pressing [EXIT] while the LCD screen is prompting for a
zone message #. Any changes will automatically be copied to all other LCD
keypads in the system. NOTE: If you want a LCD keypad to have a different custom
message, you must enable custom message lock under the [*]-[9]-[3] function.
NX-6-EUR Installation manual Page 18 23/12/04
- Series 1
- NX-6-EUR Control Panel 1
- Installation manual 1
- CONTENTS 3
- GENERAL INFORMATION 5
- ORDERING INFORMATION 5
- FEATURE DEFINITIONS 6
- GE Security 10
- PROGRAMMING THE NX-6 KEYPADS 14
- IMPORTANT REMARKS 33
- Telephone number 1 34
- Format selections 35
- Telephone number 2 37
- Telephone number 3 39
- Special formats 42
- Download parameters 43
- Entry/Exit timers 45
- General options 50
- Programming the outputs 54
- NX-6 PROGRAMMING WORKSHEETS 79
- BOARD INSTALLATION 90
- NX-6 WIRING DIAGRAM 91
- TERMINAL DESCRIPTION 92
- TECHNICAL SPECIFICATIONS 93
- CONTACT-ID AND SIA 95
- CONTACT ID 97
- EXPANDER TROUBLE 99
- CE DECLARATION 100
Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme CADDX NX-6
(18 Seiten)ParkZone PKZ4400 manuels
Manuels d'utilisation et guides de l'utilisateur pour Jouets ParkZone PKZ4400.
Nous fournissons des manuels en pdf 1 ParkZone PKZ4400 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Kommentare zu diesen Handbüchern