CADDX NX-6 Installationshandbuch PDF herunterladen (Seite 7)

GE Security

Auxiliary power overcurrent

The NX-6 will light up the “Service” LED on the keypad whenever too much current is

being drawn from any device powered by the system. This condition can be reported to

the central station (see location 37 segment 3).

A+B alarm reporting (Sweden)

When this feature is enabled, a first trigger from a zone will send a BG report

(unverified alarm or B-alarm) for that zone. The B-alarm message will be written in the

log. In addition, a fix 30 minutes timer will start. If a zone is triggered for a 2nd time

within the 30 minutes time frame, this zone will send a BA report (burglary alarm or

verified alarm) to the monitoring station. If there is no 2nd zone that was triggered within

30 minutes, the timer will be cleared. A+B alarm reporting only works with intrusion zone

types using the SIA formats. When this feature is enabled, the standard cross-zoning

feature will be in-active (see location 37 segment 3).

Box tamper

The NX-6 has an input for a normally closed tamper switch (see wiring diagram). The box

tamper can be programmed to report, and/or sound the siren and/or the keypad. These

terminals can be enabled or disabled by programming (see locations 37 segment 2 and 3,

and location 39).

Built In siren driver

The NX-6 has a built-in 112 dB siren driver. If desired, this built-in driver can easily be

converted to a 1 amp voltage output by programming (see location 37 segment 2).

Bypass toggle

This feature will enable the end user to toggle (turn on or off) the bypass of an interior

zone while the system is armed. This is done by pressing the [Bypass] key (see location

23 segment 2).

Call back

When this feature is enabled, the control panel will use the call back phone number to call

the download computer before it begins a download (see locations 21 and 22).

Cancel

If this feature is enabled, the NX-6 will send a “Cancel” report when the system is

disarmed and the [Cancel] button is pressed within 5 minutes of an alarm. Once the

[Cancel] key has been pressed, the “Cancel” LED will light up until the central station

acknowledges the “Cancel” report (see location 23 segment 3).

Chime

This feature can be turned on and off using the “chime” key. When the system is in the

disarmed state, a trip on selected zones will generate either a DING-DONG or a single

tone through the keypad sounder (depending on the keypad programming). This lowest

level of security can be enabled by zone; this is done by programming the appropriate

zone configuration for it, or by customizing its zone configuration (see locations 111-169).

Code required options

The NX-6 can be programmed to require a code in order to bypass zones and/or to

initiate a download using the [*]-[9]-[8] or [*]-[9]-[9] function (see locations 23 segment 2

and 41).

Communication formats

The NX-6 can report in multiple formats. You are recommended to use Contact ID or SIA

formats if possible. If you wish to report to a private phone (using the voice module) or to

a central station in a 4+2 format, you must program each code that is to be reported (see

locations 56-83 and 111-169).

NX-6-EUR Installation manual Page 7 23/12/04

1 2 3 4 5 6 7 8 9 10 11 12 ... 103 104

Kommentare zu diesen Handbüchern

Keine Kommentare

CADDX NX-6 Installationshandbuch Seite 7

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Sicherheitszugriffskontrollsysteme CADDX NX-6