CADDX NX-448E-I Installationshandbuch Seite 36
- Seite / 94
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
GE Security
g
Reporting events to phone number 2
Phone N°2 can be used to back up phone N°1, or as a second receiver to multi-report or
split-report events. Phone N°2 has two programming locations that are used to select the
events that are reported to this phone number. Location 10 is used to select the events
which are reported to phone N°2, and location 11 is used to select which partitions are
reported to phone N°2. If you do not want dual or split reporting, location 10 and location
11 should be left at the factory default of “0”. If you want multi-reporting or split reporting,
and the split is based on the event type (such as alarm, open close etc.), location 10
should be used to select only those events that should be reported to phone N°2, and
location 11 should be left at the factory default of “0”. If you want dual or split reporting,
and the split is based on partition, then location 10 should be programmed as “0”, and
location 11 should be used to select those partitions that are to be reported to phone N°2.
If no events are to be reported to phone N°2, both locations should be at “0”.
LOCATION 10 - EVENTS REPORTED TO PHONE N° 2 (2 segments of feature selection data)
Segment 1
1 = Alarms
2 = Opening and closings
3 = Zone bypass and bypass restores
4 = Zone trouble and trouble restores
5 =
Power fail (AC failure), low battery, power restore (AC restore) ,
and low battery restore
6 = Bell cut, bell cut restore, telephone line restore
7 = Test reports
8 = Start and end programming, download complete and log full
Segment 2
1 = Zone and box tamper
2 = Auxiliary power overcurrent, and restore
3 = Wireless sensor missing and restore
4 = Wireless sensor low battery and restore
5 =
Expander trouble and restore (keypads are considered as
expanders)
6 = Fail to communicate
7 = Alarm restore
8 = Tamper restore
LOCATION 11 - Reserved
NX-4-EUR Installation manual Page 36 08/09/04
- Series 1
- NX-4-EUR Control Panel 1
- Installation manual 1
- CONTENTS 2
- GENERAL INFORMATION 4
- ORDERING INFORMATION 4
- FEATURE DEFINITIONS 5
- GE Security 10
- PROGRAMMING THE NX-4 KEYPADS 12
- IMPORTANT REMARKS 31
- Telephone number 1 32
- Format selections 33
- Telephone number 2 35
- Telephone number 3 37
- Special formats 39
- Download parameters 40
- Entry/Exit timers 42
- General options 46
- Programming the outputs 50
- NX-4 PROGRAMMING WORKSHEETS 71
- BOARD INSTALLATION 80
- NX-4 WIRING DIAGRAM 81
- TERMINAL DESCRIPTION 82
- TECHNICAL SPECIFICATIONS 83
- CONTACT-ID AND SIA 85
- CONTACT ID 87
- EXPANDER TROUBLE 89
- CE DECLARATION 90
Verwandte Produkte und Handbücher für Empfänger CADDX NX-448E-I
Empfänger CADDX NX-408E-I Installationshandbuch
(99 Seiten)
(99 Seiten)
Empfänger CADDX NX-408E-I Spezifikationen
(16 Seiten)
(16 Seiten)
Empfänger CADDX NX-408E Spezifikationen
(16 Seiten)
(16 Seiten)
Empfänger CADDX NX-448E-I Spezifikationen
(30 Seiten)
(30 Seiten)
Empfänger CADDX NX-448E-I Installationshandbuch
(61 Seiten)
(61 Seiten)
ParkZone PKZ3400 manuels
Manuels d'utilisation et guides de l'utilisateur pour Jouets ParkZone PKZ3400.
Nous fournissons des manuels en pdf 1 ParkZone PKZ3400 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Kommentare zu diesen Handbüchern